556H Honda / Acura Immobilizer Bypass Module Installation Instruction

Download Mode 1 Mode 2 ? Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 2002-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More

Honda Civic Racing Intake Manifold Installation Instruction

Download Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve). Notes • There is no need to reinstall the fast idle valve; located on the drivers side of the rear of stock manifold ( there is no check engine light). • Due to engine mounting tolerances, the firewall may need to be clearanced. • The stock intake pipe will not fit. An aftermarket intake pipe will need to be purchased. • Modify stock map sensor / purge control valve bracket for clearance of TPS. • Use 88-91 CRX injectors and fuel regulator.… Read More

Honda Civic D-series Racing Intake Manifold Manual Installation Instructions

Download
Part # 307-05-0260 Racing Intake Manifold For Models and Years • 1992-1995 Honda Civic DX/EX (D15B7/D16Z6) • 1996-2000 Honda Civic EX (D16Y8) • 88-91 Honda CRX Si / DX* (*These models will require additional parts)
Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve).
Removal 1. Allow car to cool to ambient temperature. DO NOT attempt to work on warm or hot vehicle. 2. Drain coolant. 3. Relieve fuel pressure by loosening banjo bolt on top of fuel filter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced.… Read More

2000-2002 Acura Integra 556H Honda/Acura Immobilizer Bypass Module

Download Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 20026? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. Installation Instructions 1. Remov-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ?? steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More

555H Honda/Acura Immobilizer Bypass Module

Download Models Honda Accord: 1999-2002 Honda Odyssey: 1999-2002 Honda Prelude 1999 Acura CL 2001-2002 Acura Integra: 2001-2002 Acura MDX: 2001-2002 Acura TL: 2001-2002. Installation Instructions 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide . 3. Wire the 555H as shown in the wiring diagram. Wire Color Guide SYNCH BLUE, ORANGE/BLUE, or BLUE/WHITE DATA RED OR BLUE/GREEN KEY SENSE BLUE/WHITE. Wire Connection Guide BLUE/WHITE: Connect this wire to the (-) key sense wire at the ignition cylinder. The key sense wire rests at ground when the key is inserted into the ignition switch. BLACK: Connect this wire to a quality chassis ground (preferably scraped sheet metal) separate from other component ground locations. BLUE: Connect this wire to the BLUE status output of the remote start.… Read More

2002-2006 Acura RSX-S Throttle Body To Intake Manifold Adapter

Download Part #: KIM01 K20A/A2/A3/Z1 Throttle Body To RBC/RRB/RBB Intake Manifold Adapter This adapter provides the SOLUTION for directly bolting up a 02-06 RSX-S/ITR or 02-05 Civic Si/CTR Throttle Body to an Accord Euro R, 06-08 Civic Si, or 04-05 TSX Intake Manifold. Ease of fitment has been confirmed for the following vehicle/engine/mount combinations: -1992-199 5 Honda Civics equipped with a K20 engine and Hasport EGK1 engine mounts -1996-200 0 Honda Civics equipped with a K20/24 engine and Hasport EKK2 engine mounts -1994-200 1 Acura Integras equipped with a K20 engine and Hasport EGK1 engine mounts -2002-200 6 Acura RSX-S/Honda ITRs with a K20 engine and all available engine mounts. 1. PREPARATION 1. Remove the EVAP hose, brake booster hose, PCV hose, vacuum hose, water bypass hoses, throttle cable, fuel lines, fuel injector connectors, IAC valve connector, TP sensor connector, MAP sensor connector, and EVAP canister purge valve connector from your current intake manifold and throttle body setup.… Read More

555H Honda/Acura Immobilizer Bypass Module Manual Installation Instructions

Download
Models : Honda Accord: 1999-2002 Honda Odyssey: 1999-2002 Honda Prelude 1999 Acura CL 2001-2002 Acura Integra: 2001-2002 Acura MDX: 2001-2002 Acura TL: 2001-2002.
Product Description : The Honda/Acura Immobilizer anti-theft system uses a low-power transponder mounted in the head of the ignition key. When the vehicle is started, the Key Cylinder Module converts the transponder signal and sends a secure, coded signal to the Engine Control Module. If the signal to the Engine Control Module is correct, the vehicle will start.
Installation Instructions : 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide . 3. Wire the 555H as shown in the wiring diagram.
Wire Connection Guide : BLUE/WHITE: Connect this wire to the (-) key sense wire at the ignition cylinder.… Read More

Honda TRX 250R MSD Enhancer Ignition System Manual Installation Instructions

Download
The MSD Enhancer Ignition system, PN KT4202, for the Honda TRX 250R ATV is designed as a complete system. No part may be substituted nor should any part be used with the stock ignition components. Note: To use the MSD Enhancer Ignition System the stock flywheel and stator assembly must be modified. This modification is not reversible.
MODIFYING THE STATOR Remove the stator assembly from the engine and secure it so it can be worked on without it moving. 1. Place the two black windings (with tape sealer) facing away from you (Figure 3). Locate the two black solder posts directly below the left black winding. The post to the left is the one we will be dealing with. This post may be coated with a black sealer. This will burn off when applying the soldering gun. Figure 3 Locating the Soldering Post of the Stator. 2. Soldered to this post is a very small wire that must be removed.… Read More

Honda GXV340/GXV390 Engine Owners Manual

Download
LPG CONNECTIONS This engine is certified to comply with U.S. EPA and California ARB emission regulations using the Impco Beam regulator specified in the installation instructions (see below). Honda used this regulator and other specific parts and adjustments to demonstrate compliance with the emission regulations. Adjustable fuel system parts must have U.S. EPA and California ARB approved tamper resistant features to limit the available adjustment after the fuel system is correctly installed. If an equipment manufacturer did not install your engine in a product you will need the installation instructions for the Honda certified system (see below). If you choose not to use the Honda fuel system you must use a system that has been certified by the fuel system manufacturer to be used on this Honda engine. Or if you use a fuel system that is not already certified you must have certification test data satisfactory to the U.S.… Read More

Honda GL1800 Air Horn Front Mount Manual Installation Instructions

Download
1. Place the motorcycle on the centerstand. 2. Remove the left side cover (painted) to expose the battery. Remove the left plastic engine cover (chrome) . Remove the lower center fairing cowl or spoiler; there are 2 pull pin rivets and 6 allen screws holding this panel in place. Drop the panel down and slide it out to the right or left. 3. Horns and Mounting Bracket: Attach the large “L” shaped bracket with the split clamp to the engine guards as shown in photo #1. NOTE: Make the screws snug only! Install the horn set onto the “L” bracket using the 2 allen screws provided, tighten securely. Align the horn set to be level and to have clearance between the fairing as shown in photo #2, tighten securely. 4. Compressor: Remove the stock left hand horn and loosely re-install the 12mm mounting bolt (see photo #4A). Next as shown in photo # 3, to the compressor attach the air hose, the short red wire to the (+) positive terminal and the white wire to the (-) negative.… Read More