". You can read and download the PDF file on this page, or you can watch the video tutorial. Please use another keyword if these document aren't what you look for.
Base Timing 0°TDC (Manual Trans) Base Timing 0°TDC (Auto Trans) PROCEDURE: Set timing under the following conditions: Normal operating temperature..
Ignition timing 1994 Chev. 5.7L. This is a discussion on Ignition timing 1994 Chev. 5.7L within the Technical / Maintenance forums, part of the General Discussion.
1994 Chevrolet Silverado K1500, 350 v8, automatic transmission. With timing light attached, ignition timing retards towards TDC when throttle is.
Filed Under (Ford) by Doe Namblas on 28-01-2014
Engine Application Ford V6, 144-200; Ford V6, 171 (2600-2800cc); Ford V8, 255, 289, 302 & Boss 302, 1965-1988; Ford V8, 289-351W & Boss 302, pre 1972; Ford V8, 302-351W, 1972 & up; Ford V8, 352-428, 1964-1974; Ford V8, 351C, 351M, 400M, 1970-1982; Ford V8, 429-460, 1968-1971; Ford V8, 429-460, 1972-1987; Ford V8, 429-460 w/nine keyway crank gear; Ford V8, 351W, 351W H.O., 1969-¹84; Ford V8, 5.0L 302 H.O., 1980-March 21, 1984; Ford V8, 5.0L 302, 351W, March 22, 1984-1992.
Tools and supplies needed: 1. Basic hand tools as required for your particular camshaft and balancer bolts 2. Torque wrench 3. Pro Cam Lube (part #153 or #154) or suitable replacement 4. Camshaft Degree Kit (part #4796 including degree video) 5. Crankshaft Socket (part #4798 for Ford 302-351W, 429-460) 6. Thread locking compound 7. Engine repair manual for your particular engine.
The following instructions begin after the timing cover and old timing set have been removed.… Read More
Download Ford COMP Cams Timing Set Installation Instructions
Filed Under (Toyota) by Doe Namblas on 01-01-2014
Download 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower vehicle. 2. On MR2, remove right hood side panel and cruise control actuator. Remove right rear wheel. On Celica and Camry, remove alternator from engine and secure out of way. On Camry, remove coolant reservoir tank if it interferes with timing belt removal. Remove engine control (torque) rod from front of engine. 3. On all models, remove accessory drive belts. Using floor jack, slightly raise engine to remove weight from right (timing belt side) engine mount at timing belt cover. 4. Remove right (timing belt side) engine mount and bracket from front of engine. Remove spark plugs. Remove No. 2 timing belt cover and gaskets. See Fig. 1 . 5. Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Cylinder No.… Read More
Download 1994 Toyota Camry DX TIMING BELT REMOVAL and INSTALLATION
Filed Under (Plymouth) by Doe Namblas on 10-02-2014
Download 1. Raise vehicle on hoist and remove right front wheel. Remove right inner splash panel. Remove accessory drive belts. Remove crankshaft vibration damper. 2. Remove generator drive belt idler pulley. Remove lower timing belt cover. 3. Remove right engine support assembly vertical bolts from bottom of frame rail (timing belt end of engine). 4. Lower vehicle. Remove upper timing belt cover. Place floor jack under vehicle to support weight of engine and transaxle assembly. Remove 3 bolts attaching engine mount assembly to engine bracket. 5. Move A/C drier aside. Remove coolant reservoir tank. Remove right engine mount. Remove 3 bolts attaching engine mount bracket to engine block. 6. Rotate crankshaft clockwise to align timing marks on camshafts and oil pump housing. See Fig. 1 . 7. On models equipped with hydraulic tensioner, remove hydraulic tensioner bolts and remove tensioner. Place hydraulic tensioner in vise, and SLOWLY compress tensioner plunger. Align the holes in the tensioner body and plunger, and insert a pin through the body and plunger to lock the plunger in place.… Read More
Download 2000 Plymouth Breeze TIMING BELT Removal Inspection Installation
Filed Under (Chevrolet (Chevy)) by Doe Namblas on 07-02-2014
Download 1994 Chevy Truck C 1500 Truck 2WD V6-262 4.3L VIN Z Vehicle Level Maintenance Tune-up and Engine Performance Checks Ignition Timing Technical Service Bulletins Ignition – Timing Connector Location Change. INFORMATION SUBJECT: TIMING CONNECTOR LOCATION CHANGE MODELS: 1994 CHEVROLET AND GMC C/K TRUCKS WITH GASOLINE ENGINES The timing connector, which can be disconnected to return engine timing to base for adjustment purposes, has been moved from the engine compartment to inside the cab. This new location is not currently reflected in the Service or Owner’s Manual. The new location is under the dash directly below the glove compartment. The tan/black wire is routed for a short distance outside of a large wiring harness. This large harness is routed between the heater blower motor and evaporator case. The timing connector is taped to the wire bundle (Figure 1).… Read More
Download 1994 Chevy Truck C 1500 Ignition – Timing Connector Location Change
Filed Under (Ford) by Doe Namblas on 09-12-2013
Download Ford Timing Set Installation Instructions Thank you for choosing COMP Cams® products! We know you have options in valve train component selection and we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation, and also take a moment to review the included limited warranty information. Engine Application High Energy Magnum Hi-Tech Ford V6, 144-200 3223 Ford V6, 171 (2600-2800cc) 3236 Ford V8, 255, 289, 302 & Boss 302, 1965-1988 2120 3120 Ford V8, 289-351W & Boss 302, pre 1972 3220 Ford V8, 302-351W, 1972 & up 3230 Ford V8, 352-428, 1964-1974 3208 2108 3108 Ford V8, 351C, 351M, 400M, 1970-1982 3221 2121 3121 Ford V8, 429-460, 1968-1971 3222 2122 3122 Ford V8, 429-460, 1972-1987 2130 3130 Ford V8, 429-460 w/nine keyway crank gear 2134* Ford V8, 351W, 351W H.O., 1969-¹84 2135 3135 Ford V8, 5.0L 302 H.O., 1980-March 21, 1984 2131 3131 Ford V8, 5.0L 302, 351W, March 22, 1984-1992 2138 3138 Notes: * #2120 or #3120 should not be installed on 351W engines as they are designed for 255, 289, 302 or Boss 302 engines.… Read More
Download COMP Cams® Ford Timing Set Installation Instructions
Filed Under (Acura) by Doe Namblas on 01-01-2014
Download 1.8LB18 Series Engines The AERATechnical Committee offers the following information regarding timing belt installation procedures on 1994-2001 Acura 1.8LB18 Series engines. Failure to follow these procedures could result in engine damage. 1. Position the crankshaft and the camshaft pulleys as shown in Figure 1 before installing the timing belt. a. Set the crankshaft so that the No. 1 piston is at top dead center (TDC). Align the groove on the teeth side of the timing belt drive to the “arrow mark” pointer on the oil pump. b. Align the TDC marks on intake and exhaust pulleys. 2. NOTE: To set the camshafts at TDC position for the No. 1 piston, align the holes in the camshafts with the holes in No. 1 camshaft holders and insert 5.0 mm pin punches in the holes. 3. Install the timing belt tightly in the sequence shown in Figure 2. 1) Timing belt drive pulley (crankshaft) 2) Adjusting pulley 3) Water pump pulley 4) Exhaust camshaft pulley 5) Intake camshaft pulley 4.… Read More
Download 1994-2001 Acura Timing Belt Installation Procedure
Filed Under (Ford) by Doe Namblas on 06-06-2013
Download 1997 Ford Truck F 150 2WD Pickup V8-5.4L SOHC VIN L Vehicle Level Engine, Cooling and Exhaust Engine Timing Chain Service and Repair Installation Installation. NOTE: Ford does not provide a procedure to align the timing components without the OE tools specified. 1. Compress the tensioner plunger, using an edge of a vise. CAUTION: Timing chain procedures must be followed exactly or damage to valves and pistons will result. Do not compress the ratchet assembly. This will damage the ratchet assembly. 2. Use a small screwdriver or pick to push back and hold the ratchet mechanism. 3. While holding the ratchet mechanism, push the ratchet arm back into the tensioner housing. 4. Install a paper clip into the hole in the tensioner housing to hold the ratchet assembly and plunger in during installation. 5. Remove the tensioner from the vise. 6. Check the illustrated components for part number orientation. 7.… Read More
Download 1997 Ford Truck F 150 Timing Chain Installation
Filed Under (Saturn) by Doe Namblas on 10-12-2013
Download 2003 Saturn Truck VUE V6-3.0L VIN B Timing Belt: Service and Repair Timing Belt Replacement Removal Procedure 1. Remove the front timing belt cover. 2. Rotate the crankshaft using the J 42098 until the #1 cylinder is at 60 degrees before top dead center (BTDC). 3. Install the J 42069 Crankshaft Locking Tool. 4. Rotate the crankshaft in the engine rotational direction (clockwise) using the J 42098 until the #1 cylinder is at top dead center (TDC) and tighten the lever arm to the water pump pulley flange. Important: Ensure that the alignment of the crankshaft is not 180 degrees off. The alignment mark must align with the corresponding notches on the rear timing belt cover. 5. Install the 1-2 and 3-4 camshaft locks, the J42069-1 Timing Belt Alignment Kit and the J42069-2. Important: Do not rotate the crankshaft if the camshafts are not locked in place with the 1-2 and 3-4 camshaft locks (J42069-1 and J42069-2).… Read More
Download 2003 Saturn Truck VUE V6-3.0L VIN B Timing Belt: Service and Repair
Filed Under (Honda) by Doe Namblas on 31-12-2013
Download Special Tools Required ?Holder Handle 07JAB-001020A ?Holder Attachment, 50 mm, Offset 07MAB-PY3010A ?Socket, 19 mm 07JAA-001020A or a commercially available 19 mm socket NOTE: ?If you are installing the timing belt and the balancer belt, go to step 1. ?If you are installing only the balancer belt, go to step 7. 1. Remove and clean the balancer belt drive pulley. 2. Clean the timing belt pulleys, and the upper and lower timing cover. 3. Set the crankshaft to TDC. Align the dimple (A) on the tooth of the timing belt drive pulley with the pointer (B) on the oil pump. 4. Clean the camshaft pulley and set it to TDC. 5. Install the timing belt in a counterclockwise sequence, starting with the drive pulley. -1 The ”UP” mark (A) on the camshaft pulley should be at the top. -2 Align the TDC grooves (B) on the pulley with the top edge of the head.… Read More
Download 2002 HONDA ACCORD – Timing Belt and Balancer Belt Installation
Filed Under (Honda) by Doe Namblas on 31-12-2013
Download 2001 Honda Prelude L4-2157cc 2.2L DOHC (VTEC) MFI Vehicle Level Engine, Cooling and Exhaust Engine Timing Belt Service and Repair Removal and Installation. REMOVAL NOTE: * Turn the crankshaft pulley so the No. 1 piston is at Top Dead Center (TDC) before removing the belt. * Inspect the water pump after removing the timing belt. * Replace the timing belt and timing balancer belt at 105,000 miles (168,000 km) according to the maintenance schedule (normal conditions/severe conditions). If the vehicle is regularly driven in one or more of the following conditions, replace the timing belt and timing balancer belt at 60,000 miles (U.S.A.) 100,000 km (Canada). * In very high temperatures (over 110°F, 43°C). * In very low temperatures (under -20°F, -29°C). 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the radio’s preset buttons. 2. Disconnect the battery negative terminal first, then the positive terminal.… Read More
Download 2001 Honda Prelude Timing Belt Removal and Installation