1993 cadillac deville replace ignition switch

You search Auto repair manual PDF about 1993 cadillac deville replace ignition switch, search results will appear below. If search results do not exist, please search by others keyword.

2000 Cadillac DeVille Brake Switch Circuit Low Input

Filed Under (Cadillac) by admin on 06-04-2014

Download . Circuit Description The torque converter clutch (TCC) brake switch is used to indicate the status of the brake pedal (applied or released). If the PCM detects an open TCC brake switch (stuck ON) during accelerations, then DTC P0719 sets. DTC P0719 is a type C DTC. Conditions for Running the DTC * No VSS DTCs P0502 or P0503. * DTC P0719 has not passed this ignition cycle. Conditions for Setting the DTC The TCC brake switch input is at 0 volts for 15 minutes and the following conditions occur 8 times without a status change on the TCC brake input: * The vehicle speed is less than 8 km/h (5 mph). * The vehicle accelerates to 32 km/h (20 mph) within 2-6 seconds. * Then the vehicle speed remains above 32 km/h (20 mph) for 6 seconds. Action Taken When the DTC Sets * The PCM does not illuminate the malfunction indicator lamp (MIL).… Read More

2000 Volkswagen Cabrio Ignition Switch: Service and Repair

Filed Under (Volkswagen (VW)) by admin on 02-01-2014

Download Steering column, assembly WARNING:Special safety precautions and some different procedures apply to vehicles equipped with airbags CAUTION:Before working on the electrical system: Obtain radio anti-theft code. Ignition OFF ! Disconnect battery Ground (GND) strap. Note: After reconnecting battery: Activate vehicle equipment such as radio, clock and power windows as per service procedures and/or Owner’s Manual. On vehicles equipped with OBD II, activate readiness code. Refer to Powertrain Management, Computers and Control Systems, Testing and Inspection, Procedures See: Powertrain Management/Computers and Control Systems/Testing and Inspection For further information on the steering column assembly, refer to Steering and Suspension, Steering, Steering Column, Service and Repair. 1.- Horn pad -Removing, Fig. 1 2.- Horn plate -Removing, Fig. 2 3.- 50 ±10 Nm (37 ±7 ft lb) 4.- Steering wheel -Horn contact ring, Fig. 3 -Lubricate horn ring with universal grease 5.- Steering column switch securing screws 6.- Combination switch -Turn signal switch. -E2- -Headlight dimmer/flasher switch -E4- -Emergency flasher switch -E3- -Removing, Fig.… Read More

1990-1998 GM Cadillac Deville Ignition Lock Cylinder REMOVAL & INSTALLATION

Filed Under (Cadillac) by admin on 28-03-2014

Download When performing service around Supplemental Inflatable Restraint (SIR) system components or wiring, the SIR system must be disabled. Failure to do so could result in possible air bag deployment, personal injury, or unneeded SIR system repairs. Catera Disconnect the negative battery cable. 1. Remove the steering wheel. 2. Remove the inflatable restraint steering wheel module coil. 3. Insert a small pointed awl or wire into the ignition lock cylinder release pinhole. 4. Pull out the ignition lock cylinder. 5.Fig. Insert a pointed tool into the release pin hole To install: Install the lock cylinder. Look into the hole that receives the lock cylinder on the lower RH side in order to locate the locking lever. 1. Carefully push down on the locking lever using a small flat-bladed tool until an audible click is heard. 2. Place the lock cylinder into the empty hole. 3. 6. Install the inflatable restraint steering wheel module coil.… Read More

1993 Ford Escort FUEL PUMP CIRCUIT (RELAY & INERTIA SWITCH)

Filed Under (Ford) by admin on 31-12-2013

Download 1993 Ford Escort G – TESTS W/CODES – EEC-IV (1.9L)’ ’1993 ENGINE PERFORMANCE Ford Motor Co. – Self-Diagnostics – EEC-IV. CIRCUIT TEST J – FUEL PUMP CIRCUIT (RELAY & INERTIA SWITCH) Diagnostic Aids When ignition switch is in the ON or START position, the PCM connects FUEL PUMP circuit (PCM terminal No. 22) to ground. The fuel pump relay is energized and electrical current flows to the fuel pump. If PCM does not receive ignition PIP signal within 2 seconds, FUEL PUMP circuit is opened and fuel pump operation is terminated. Perform this test when instructed by QUICK TEST or CIRCUIT TEST AA. This test is only intended to diagnose: * Fuel pump relay. * Inertia Fuel Shutoff (IFS) switch. * Wiring harness circuits (B+, VPWR, FUEL PUMP, GND and POWER-TO-PUMP). * Faulty Powertrain Control Module (PCM). Fig. 31: Fuel Pump Monitor Circuit Diagram (Escort & Tracer) 1)Code 87/556: Check VPWR To Fuel Pump Relay Code 87/556 indicates a fuel pump primary circuit failure.… Read More

Diagnostic Information for Intermittent Vehicle No Crank/Dead Battery

Filed Under (Other Manuals) by admin on 26-12-2013

Download Models: 2004 Buick Rainier 2000-2004 Cadillac Escalade 2002-2004 Cadillac Escalade EXT 2003-2004 Cadillac Escalade ESV 1998-2004 Chevrolet Blazer, S-10 Pickup 1999-2004 Chevrolet Silverado 2000-2004 Chevrolet Suburban, Tahoe 2002-2004 Chevrolet Avalanche, TrailBlazer, TrailBlazer EXT 2003-2004 Chevrolet Express 1998-2004 GMC Jimmy/Envoy, Sonoma 1999-2004 GMC Sierra 2000-2004 GMC Yukon, Yukon XL 2002-2004 GMC Envoy, Envoy XL 2003-2004 GMC Savana 2004 GMC Envoy XUV 1998-2004 Oldsmobile Bravada 2003-2004 HUMMER H2. #04-06-03-002: Diagnostic Information for Intermittent Vehicle No Crank/Dead Battery – (Feb 5, 2004) When diagnosing a concern regarding an intermittent vehicle no crank or dead battery, technicians should remove and reinstall the ignition switch using the Ignition Switch Replacement procedure in the Steering Wheel and Column section of SI. The ignition switch may have been misindexed in the steering column during a previous replacement . If the ignition switch is misindexed in one direction, the ignition switch circuits will not be completely open when the ignition switch is in the OFF position with the key removed.… Read More

1994 Cadillac DeVille Concours Passive Struts

Filed Under (Cadillac) by admin on 01-01-2014

Download Subject: Procedure to Disable Illumination of Service Indicator AFTER the Installation of Passive Struts/Shocks Models: 1992-94 Buick Skylark 1993-96 Buick Park Avenue 1989-92 Cadillac Allante 1991-93 Cadillac Eldorado, Seville 1991-95 Cadillac DeVille 1991-95 Oldsmobile Ninety Eight 1992-93 Oldsmobile Achieva 1994-99 Pontiac Bonneville This bulletin is being revised to clarify when this bulletin may be used to turn the service suspension lamp off. Also, a step has been added to the 1991 Cadillac Eldorado and Seville repair. Please discard Corporate Bulletin Number 00-03-11-001 (Section 3 – Suspension). Refer to the Service Manual page 8D-13 (1989) or 8D-14 (1990-1992). On these vehicles, adjust the BCM Override value “BS08″. To do this, use the warmer/cooler button on the CCDIC to decrease the BCM override value “BS08″ which is displayed when you enter the system by two (2). When the desired number is displayed on the CCDIC, it must be stored by holding the “Elapsed Time” and “Fuel Used” buttons until the new value flashes on and off.… Read More

Steering Lock Cylinder – Ignition Switch Removing and Installing

Filed Under (Other Manuals) by admin on 09-12-2013

Download Removing – Remove driver’s-side airbag unit and steering wheel. Repair Manual, Body Interior, Repair Group 69 – Remove steering column switches Page 94-37 . – Insert spare or shop key and switch ignition on: access hole will appear in front of switch next to ignition key slot. Installing – Insert length of steel wire or small screwdriver (approx. 2 mm dia.) as far as it will go, as illustrated, and pull lock cylinder out of steering lock housing in direction of arrow. – Ignition switch must be in “ignition on” position. – Push lock cylinder with ignition key all way into steering lock housing and press in firmly until catch engages audibly. – Install steering column switches and steering wheel. Ignition switch, removing and installing Removing Note: It is not necessary to remove the lock cylinder. – Disconnect battery Ground (GND) strap. – Remove driver’s-side airbag unit and steering wheel.… Read More

2001 Chevrolet Chevy K Silverado Transmission Stuck in Second or Third Gear

Filed Under (Chevrolet (Chevy)) by admin on 19-12-2013

Download Malfunction Indicator Lamp (MIL) On, Transmission Stuck in Second or Third Gear, Instrument Cluster Inoperative (Verify and Repair Source of Voltage Loss In Transmission Solenoid Power Supply Circuit ) Models: 2006 and Prior GM Passenger Cars and Light Duty Trucks 2005-2006 HUMMER H2 2006 HUMMER H3 2005-2006 Saab 9-7X with 4L60-E, 4L65-E, 4L80-E or 4L85-E Automatic Transmission (RPOs M30, M32, M33, MT1, MN8) Condition Some customers may comment on one or more of the following conditions: Upon investigation, one or all of the diagnostic trouble codes (DTCs) P0740, P0753, P0758, P0785, P0787, P0973, P0976, P1860, P2761, P2764 and P2769 may be set depending on the vehicle. Cause The most likely cause of this condition may be a loss of voltage to the transmission solenoid power supply circuit. This condition may also be the result of an incorrect installation of an aftermarket electronic device such as a remote starter or alarm system.… Read More

Ford 2.3 L Engine DISTRIBUTORLESS IGNITION SYSTEM INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 09-02-2014

Download CAUTION: MAKE SURE THE IGNITION SWITCH IS OFF!! The wire from the ignition switch to the ignition coil primary terminal is NOT fused in many applications. If this wire is allowed to touch vehicle or engine ground, with the ignition switch on, it can cause a direct short on the battery possibly causing permanent damage to the vehicle wiring and a fire. Cypress Engineering assumes no liability for damage caused from this occurrence or due to any faults in the existing vehicle wiring. 5. Remove the ignition switch wire from the ignition coil primary positive (+) terminal. Make sure this wire does not come into contact with vehicle or engine ground. 6. Remove the ignition coil and mounting strap from the fan housing and set them aside. 7. Remove the stock distributor and set it aside. 8. Install the Compu-Tronix DIS4-2.3 L Ford Electronic Distributor. Tighten the clamp just enough so that the distributor can still be turned by hand.… Read More

2002 Cadillac DeVille DHS V8-4.6L VIN Y

Filed Under (Cadillac) by admin on 31-12-2013

Download 2002 Cadillac DeVille DHS V8-4.6L VIN Y Recall – Fuel Tank Pressure Sensor Malfunction. Product Safety – Fuel Tank Pressure Sensor # 03038A – (03/17/2004) 03038A — Fuel Tank Pressure Sensor 2002-2003 Cadillac DeVille, Seville Equipped with V8 (4.6L) Engine (LD8/L37) 2002-2003 Oldsmobile Aurora Equipped with V8 (4.0L) Engine (L47) 2002-2003 Pontiac Bonneville SSEi This bulletin is being revised to remove the parts restriction on the fuel tank and eliminate the need for the recall identification label. Please discard bulletin 03035, issued October 2003. Condition General Motors has decided that a defect which relates to motor vehicle safety exists in certain 2002-2003 model year Cadillac DeVille and Seville vehicles equipped with a V8 (4.6L) engine (LD8/L37), Oldsmobile Aurora vehicles equipped with a V8 (4.0L) engine (L47), and Pontiac Bonneville SSEi vehicles. The fuel tank pressure sensors in these vehicles are unusually susceptible to malfunctions. If the sensor malfunctions, excessive vacuum can be applied to the fuel tank during self-diagnostic testing.… Read More

You might also likeclose