1997 Ford Aerostar/Ranger Wheel Hubs and Bearings, Front Wheels, 4-Wheel Drive DISASSEMBLY AND ASSEMBLY

Download Wheel Grease Seal and Bearing, Front Replacement and Repacking SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Impact Slide HammerT50T-100-A Bearing Cup ReplacerT80T-4000-P Driver Handle T80T-4000-W Seal Replacer T80T-4000-T Spindle Seal ReplacerT95T-3132-D. The recommended wheel bearing lubricant is lithium-base High-Temperature Constant Velocity Joint Grease E43Z-19590-A or equivalent meeting Ford specification ESP-M1C207-A. -base grease is not compatible with lithium-base grease. Do not intermix. Clean all old lubricant grease prior to lubricating front/rear wheel bearing. Use of incompatible bearing lubricant could result in premature lubricant breakdown. NOTE: If bearing adjustment does not eliminate looseness or rough and noisy operation, clean, inspect and repack the hub and wheel bearings with specified wheel grease. If wheel bearing cup or the cone and roller assemblies are worn or damaged, they should be replaced. Manual Locking Hub, Ranger. Disassembly 1. Raise the vehicle and install Rotunda Car/Truck Stands 077-00018 or equivalent. 2. Remove the wheel and tire assembly.… Read More

2000-2005 Ford Explorer Wheel Bearings REMOVAL & INSTALLATION

Download 1. Before servicing the vehicle, please familiarize yourself with safety procedures. 2. Remove the axle”to”wheel hub retainer nut and washer. 3. Remove the parking brake shoes. 4. Press the outboard CV”joint until it is loose from the hub. 5. Remove and discard the toe link”to”wheel knuckle nut. 6. Remove the bolt and separate the toe link from the wheel knuckle. 7. Remove and discard the upper arm”to”wheel knuckle nut. 8. Remove the bolt and separate the upper arm from the wheel knuckle. 9. Remove and discard the lower arm”to”wheel knuckle nut. 10. Remove the lower arm”to”wheel knuckle bolt. 11. Remove the wheel knuckle. 12. Using a suitable press, remove and discard the wheel hub. 13. Remove and discard the wheel bearing retainer ring. 14. Using a suitable press, remove the wheel bearing. Fig. Rear hub/bearing Assembly”Aviator, Explorer and Mountaineer Fig. Pressing out the bearing 1. Installation is the reverse of the removal procedure.… Read More

2000 Ford F-150 Rear Drive Axle/Differential

Download 1. WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning off the air suspension switch located in the RH kick panel area. Failure to do so can result in unexpected inflation or deflation of the air springs, which can result in shifting of the vehicle during these operations. Raise and support the vehicle. 2. Remove the wheel and tire assembly. 3. Remove the differential housing cover (4033). ? Drain the lubricant. For additional information, refer to Differential Housing Cover in this section. 4. Remove the brake calipers and discs. 5. Remove the differential pinion shaft (4211). 1. Remove and discard the differential pinion shaft lock bolt. 2. Remove the differential pinion shaft. 6. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves. Remove the U-washers (4N237). 1.… Read More

Honda 400EX Wheel Hub Manual Installation Instructions

Download
Please follow these installation instructions carefully! Without proper installation, premature wear and failure can occur! 1. Remove all contents from its packaging and verify that all parts are present and free from damage. You should have the following items: (2) wheel hubs (2) smaller tapered bearings (2) large tapered bearings (2) wheel bearing nuts (2) dust caps (2) inner bearing seals (6) M3 x .5 screws (2) cotter pins (2) inner bearing spacers 2. Completely remove the old hubs from your quad and clean the spindle and the surrounding areas. It is very important to keep the new bearings and seals clean during installation for long life. Be sure to remove the factory inner bearing spacers from the spindle and discard. They will not be used in re-assembly. 3. Pack your new Timken tapered wheel bearings with a liberal amount of high quality wheel bearing grease. A wheel bearing packer works best, however you can accomplish the task by placing the grease in the palm of your hand and manually working it in between the bearing rollers.… Read More

TSB 4 WHEEL DRIVE/ALL WHEEL DRIVE WITH CONTROL TRAC

Download FORD: 1997-2008 Expedition, Explorer 2006-2008 F-150 2007-2008 Explorer Sport Trac 2008 F-150 LINCOLN: 1998-2008 Navigator 2003-2005 Aviator MERCURY: 2005 Mountaineer 2006-2008 Mountaineer. ISSUE: Various 1997-2008 vehicles equipped with either 4 wheel drive or all wheel drive and equipped with control trac may exhibit a shudder on acceleration/deceleration, binding in slow speed turns or noise from the front driveline and/or transfer case. The shudder/binding will occur with the vehicle being operated in the awd/auto 4×4 mode. The shudder/binding may be due to incorrect tire circumference or improper tire inflation pressures. ACTION: Follow the Service Procedure steps to correct the condition. SERVICE PROCEDURE 1. Review the tire label for correct tire size and tire inflation pressures located at the B-Pillar of the driver’s door. 2. If the tire size does not match the label, this procedure does not apply, follow normal Workshop Manual (WSM) diagnostics. 3. If the tire size is correct, ensure tire pressures are within specifications.… Read More

1990 – 1995 Ford Taurus Mercury Sable Radio Replacement Installation Instructions

Download Remove Factory Radio STEP 1 : The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in the shape as shown in the photos above. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash. Unplug the antenna cable from the rear of the radio. Unplug the 2 wire harness connectors from the rear of the radio. This vehicle may have the Ford Premium Sound System installed in the vehicle. When you pull the Ford radio out of the dash, there may be a square connector plugged into the rear of the Ford radio. If there is a square plug, then your vehicle has amplifiers.… Read More

Honda 400EX Hub installation instructions

Download
Thank you and congratulations !!!!! You have purchased the best wheel hub available for your Honda 400EX. With careful installation and a regular maintenance schedule, these will be the last set of hubs that you will ever need to buy. Please follow these installation instructions carefully! Without proper installation, premature wear and failure can occur! 1. Remove all contents from its packaging and verify that all parts are present and free from damage. You should have the following items: (2) wheel hubs (2) smaller tapered bearings (2) large tapered bearings (2) wheel bearing nuts (2) dust caps (2) inner bearing seals (6) M3 x .5 screws (2) cotter pins (2) inner bearing spacers 2. completely remove the old hubs from your quad and clean the spindle and the surrounding areas. It is very important to keep the new bearings and seals clean during installation for long life. Be sure to remove the factory inner bearing spacers from the spindle and discard.… Read More

2000 BMW 528i (E39) Front Wheel Bearing

Download 2000 BMW 528i (E39) L6-2793cc 2.8L DOHC (M52 TU) Vehicle Level Steering and Suspension Wheels and Tires Wheel Bearing Service and Repair Front Wheel Bearing. Replacing Front Wheel Bearing ( Wheel Hub )(Basis) Caution! Bearing cannot be dismantled. Do not wash out bearings. Remove brake disk (brake line remains connected), refer to Brakes and Traction Control; Disc Brake System. Remove ABS impulse sensor. Remove stabilizer link from stabilizer, Steering and Suspension. Unfasten nut. Installation: Use washer (1). Tapered spigot and bore both free of grease. Replace self-locking nut. Brace on hexagon socket if necessary. Tightening Torque, refer to Steering Specifications. Press off track rod with special tool 31 2 240. Mark the installation position of the spring strut tube (1) in the swivel bearing (2) with paint – never mark with scribing tool. Marking is not required if the factory mark is still identifiable. R installation position of right spring strut tube L installation position of left spring strut tube Version with factory marking above the swivel bearing.… Read More

1983-1990 FORD BRONCO II AUTOMATIC LOCK HUB DIAGNOSIS

Download FORD: 1983-1990 BRONCO II 1983-1995 RANGER 1991-1994 EXPLORER WHEEL END NOISE (BUZZING) IN 4X2, AFTER ISSUE UNLOCKING HUBS, SHORTLY AFTER 4X4 system diagnosis can be difficult at times due FOUR-WHEEL DRIVE USAGE: to system complexities. •Noise concerns in two-wheel drive shortly after ACTION shifting from four-wheel drive and unlocking hubs, can occur if one of the hublocks fails to For general system operation and diagnosis: Refer disengage. As the vehicle moves forward, the one to TSB Article No. 92-1-8. (1) hublock that has failed to disengage will rotate its axle shaft through the differential and attempt For specific automatic lock hub diagnosis and to rotate the other axle shaft in the opposite service: Refer to this article. direction. This is called differential motoring HUBLOCK DIAGNOSTICS torque. As this torque attempts to turn the other axle shaft through the differential gears, that WHEEL END CONTAMINATION: shaft’s hublock will attempt to engage which will •All compact vehicle hublocks have an O-ring seal result in a ratcheting or buzzing noise.… Read More

429-460 Ford V8 ACCU-DRIVE CAM GEAR DRIVE SYSTEM INSTALLATION INSTRUCTIONS

Download POWER PACKAGE: Edelbrock Accu-Drive gear drives are part of a Total Power Package parts system that can be completed with the use of dyno- matched Performer , Performer RPM, or Torker II cams, intake manifolds, and carburetors. For competition applications, use Edelbrock Victor intake manifolds. Please refer to the Power Package Guide in the Edelbrock catalog to select all the components you need.  ACCU-DRIVE OPERATING PRINCIPAL The Accu-Drive system utilizes a free floating idler gear that is self-aligning and connects the crankshaft and camshaft gears into proper mesh. The large floating idler gear is positioned on the right side of the engine (passenger side). During normal operation, the drive power is transmitted from the crankshaft through the large floating idler to the camshaft gear. During the running operation, there is no backlash between these gears. The small idler gear (located opposite the large idler gear) is also free floating.… Read More