06 kia sorento blend air actuator

You search Auto repair manual PDF about 06 kia sorento blend air actuator, search results will appear below. If search results do not exist, please search by others keyword.

1999 Chrysler Truck Blend Door Actuator Replacement

Filed Under (Chrysler) by admin on 12-03-2014

Download 1999 Chrysler Truck Town & Country LWB FWD V6-3.8L VIN L Vehicle Level Heating and Air Conditioning Air Door Air Door Actuator / Motor Service and Repair Blend Door Actuator Replacement. REMOVAL The air conditioning system can be equipped with either a standard, single blend- air door actuator, or it can be equipped with dual actuators. The dual system has separate blend-air controls. This allows for separate control of the driver’s side air, and the passenger side air. 1. Remove the lower left side steering column cover. Refer to Instrument Panel and Systems. 2. Remove ABS control module. 3. Remove blend-air actuator connector. 4. Remove blend-air actuator. INSTALLATION 1. For installation, reverse the above procedures. 2. Perform the HVAC Control Calibration Diagnostic and Cooldown test. Repeating the test is necessary to clear the fault codes.… Read More

2003 BMW 325I Sport Wagon Check engine light on and fault codes stored

Filed Under (BMW) by admin on 19-03-2014

Download 2002 BMW 325I 2.5L 2003 BMW 325I Sport Wagon 2.5L, Eng Des M54, USA Customer Concern: Check engine light on and fault codes stored. Vehicle running normally. Tests/Procedures: 1. Based upon stored fault codes for secondary air system, there is little or no flow of secondary air into engine. Typical causes for this issue are failed secondary air pumps and/or secondary air check valves. Secondary air pump should operate under normal circumstances when vehicle is first started to perform system test. Pump will normally be heard running when standing in front right corner of vehicle. 2. The secondary air pump is located in the right front of engine compartment. A secondary air pump relay located in the glove box is controlled by the engine control module and sends power to the secondary air pump. 3. Air pump can be disconnected and supplied with power and ground at pump to verify operation is possible.… Read More

2004-2008 FORD F150 2WD & 4WD HEAVY LOADS HP10004 AIR SUSPENSION KIT

Filed Under (Ford) by admin on 02-01-2014

Download FORD F150 INSTALLATION MANUAL – L5681 PG. 2 Thank you and congratulations on the purchase of a Pacbrake air suspension kit. IMPORTANT: This air suspension kit will not increase the GVWR (Gross Vehicle Weight Rating), as the GVWR is determined by the axle rating. Do not exceed the maximum capacity listed by the vehicle manufacturer. Before starting, ensure the application information is correct for the make, model and year of the vehicle you are installing it on. Please read the entire installation manual prior to starting the installation to ensure you can complete the installation once started. Pacbrake recommends using a good quality anti-seize on all fasteners, this will reduce the chances of corrosion of the fasteners, and help facilitate removal if required at a later date. 1 PREASSEMBLY OF THE AIR SPRINGS 1. Install the roll plate (with the rounded end towards the air spring) on to the bottom of the air spring.… Read More

Honda/Acura Kit 60815 Air Lift 1000 System Manual Installation Instructions

Filed Under (Acura) by admin on 26-11-2013

Download
PREPARING THE VEHICLE: 1. Jack up the rear of the vehicle or raise on a hoist. Support the frame with safety stands so that the wheels hang (fig. 1). Remove the wheels. 2. Position a floor jack at the connecting point of the lower control arm (under the attaching flange bolt) and knuckle (fig. 2). 3. Remove the flange bolt that connects the lower control arm to the knuckle. THE LOWER CONTROL ARM IS UNDER PRESSURE FROM THE COIL SPRING. USE CAUTION DURING THIS STEP FOR SAFETY PURPOSES. 4. Lower the floor jack gradually until tension is released and the coil spring can be removed. It may be necessary to remove the lower shock bolt in order for the lower control arm to move far enough to remove the coil spring. 5. Remove the coil spring. 6. Unbolt and discard the jounce bumper and mounting bolt (fig. 2).
INSTALLING THE AIR SPRING: 1.… Read More

2000-2003 Ford Focus 2.0L Zetec 21-450 COLD AIR SYSTEM Installation Instructions

Filed Under (Ford) by admin on 11-01-2014

Download The AEM Cold Air System differs from all others in several ways. We take the inlet air from outside of the engine compartment where the inlet air is considerably cooler than the hot underhood air. The cooler inlet air temperature translates to more power during the combustion process because cool air is denser than warm air. AEM has conducted extensive inlet air temperature studies and we have seen temperature reductions of up to 50 degrees by pulling air from outside of the engine compartment. The air mass flow to the engine is increased because of the increased airflow and reduced inlet temperature, which translates to more power. The AEM Cold Air Systems are 50 states Street Legal (some models and years still pending) and come with complete instructions for ease of installation. Read and understand these instructions BEFORE attempting to install this product. 1) Getting started a) Make sure vehicle is parked on a level surface.… Read More

1993-1999 Peugeot 306 Part 57-0509 Installation Guide

Filed Under (Peugeot) by admin on 24-01-2014

Download Parts list: 1 x Air filter Element 1 x Cold Air Hose Assembly 1 x Literature Pack Fixing kit: – 1 x #48 Hose Clamp 4 x Plastic Ties. INSTALLATION INSTRUCTIONS 1. Disconnect the negative battery terminal from the battery. 2. Unclip, unbolt and remove the air box intake pipe from the vehicle. (Fig. 1) 3. Unclip, unbolt and remove the air box to engine intake pipe from the vehicle. (Fig. 2&3) 4. Remove the rubber seal from the air box neck. (Fig. 4) 5. Using a junior hacksaw cut 4 x 1mm wide slits equally spaced around the air box neck. Remove any loose plastic from the air box (Fig. 5) 6. Unclip the base from the airbox and remove the original filter element. (Fig. 6) 7. Using a hot air gun gently warm the air box neck to aid fitting of the Air filter assembly. 8. Feed the Air filter assembly into the air box and through the air box neck.… Read More

2002 – 2003 Honda Civic Si & Acura RSX Comptech Icebox Cold Air Intake Installation Instructions

Filed Under (Honda) by admin on 31-12-2013

Download Parts List: 1- Icebox lid w/ screws 1- Icebox Bottom 1- Lower Air Horn 1- Filter Elbow 1- 6 mm x 35 mm screw 1- 6 mm nut 1- Plastic pin 1- High Flow Filter Element 1- Filter Oil 1—CARB EO# Decal (RSX). Step #1 Remove Stock Airbox • Before disconnecting battery locate radio code to reactivate radio after installation. (write down preset channels for later use) •Disconnect Negative battery terminal. •Remove battery positive terminal, tie down clamp, battery and plastic tray. •Remove engine cover around throttle body on intake manifold (A). •Remove stock air box lid and filter. •Disconnect Intake Air Temperature (IAT) sensor, remove upper intake hose and clamps (B). •Remove air box mounting bolts and nut. Rotate air box forward and out. Remove rubber grommets and stepped bushings from stock air box*. •Remove Lower Air inlet hose by removing mounting bolt from radiator cross support above cooling fan.… Read More

Honda Civic Si Acura RSX Icebox Cold Air Intake Manual Installation Instructions

Filed Under (Acura) by admin on 01-01-2014

Download
Parts List: 1- Icebox lid w/ screws 1- Icebox Bottom 1- Lower Air Horn 1- Filter Elbow 1- 6 mm x 35 mm screw 1- 6 mm nut 1- Plastic pin 1- High Flow Filter Element 1- Filter Oil 1—CARB EO# Decal (RSX).
Step #1 Remove Stock Airbox • Before disconnecting battery locate radio code to reactivate radio after installation. (write down preset channels for later use) •Disconnect Negative battery terminal. •Remove battery positive terminal, tie down clamp, battery and plastic tray. •Remove engine cover around throttle body on intake manifold (A). •Remove stock air box lid and filter. •Disconnect Intake Air Temperature (IAT) sensor, remove upper intake hose and clamps (B). •Remove air box mounting bolts and nut. Rotate air box forward and out. Remove rubber grommets and stepped bushings from stock air box*. •Remove Lower Air inlet hose by removing mounting bolt from radiator cross support above cooling fan.… Read More

2002-2003 Acura RSX Icebox Cold Air Intake Installation Instructions

Filed Under (Acura) by admin on 11-01-2014

Download Honda Civic Si & Acura RSX Icebox Cold Air Intake Installation Instructions (2002-2003 Honda Civic Si) (2002-2003 Acura RSX—All) Step #1 Remove Stock Airbox • Before disconnecting battery locate radio code to reactivate radio after installation. (write down preset channels for later use) •Disconnect Negative battery terminal. •Remove battery positive terminal, tie down clamp, battery and plastic tray. •Remove engine cover around throttle body on intake manifold (A). •Remove stock air box lid and filter. •Disconnect Intake Air Temperature (IAT) sensor, remove upper intake hose and clamps (B). •Remove air box mounting bolts and nut. Rotate air box forward and out. Remove rubber grommets and stepped bushings from stock air box*. •Remove Lower Air inlet hose by removing mounting bolt from radiator cross support above cooling fan. •Remove ground strap bracket on side of transmission (C). Relocate ground strap from transmission bracket to top of transmission (D). Step #2 Install Comptech Airbox •Install (3) stock rubber grommets* (E) through large holes on underside of mounting ears on Icebox (a small dab of filter oil may be used to ease this process).… Read More

Honda VTX 1800 Big Air Kit (BAK) Installation Instructions

Filed Under (Honda) by admin on 13-01-2014

Download INCLUDED IN THE KIT: (1) BAK Cover (1) Re-usable Performance Air Filter (1) Filter Raincoat (1) Mounting Post (4) M5x40 Stainless Cap Screws (2) M5x10 Stainless Cap Screws (1) Baron VTX 1800 BAK Backing Plate (1) Baron Backing Plate Adapter (2) 1/4-28 x 1 13/16″ Zinc Hex Bolts (2) 1/4″ Lock Washers (2) Aluminum Filter Spacers (3) M6x16 Hex Flange Bolts (3) External Tooth Washers (1) Reed Valve Block Off Kit BA-2561-00 (1) 3/8″ Nylon Nipple Pre-installed (1) 1/2″ Nylon Nipple Pre-installed TOOLS REQUIRED: Factory Service Manual 3, 4 & 5 mm Allen Wrenches 10, 12 & 14mm Sockets 12 & 14mm Wrenches INSTRUCTIONS: 1. Remove fuel tank per Honda service manual instructions. 2. Remove air filter box by taking out air filter element and the 4 screws around air funnels. 3. Disconnect electrical fitting from the IAT sensor (intake air temp sensor). 4. Disconnect two hoses on back of air box.… Read More

You might also likeclose