2001-2005 Honda Civic EX Air Intake Manual Installation Instructions


Filed Under (Honda) by admin on 16-02-2014

Bomz Racing 01-05 Honda Civic EX Air Intake Installation Guide Removal of Factory Intake 1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable. 2. Disconnect the air temperature sensor electrical connection. 3. Unclip the battery cable from the air inlet duct. 4. Loosen and remove the two bolts that secure the air inlet duct. 5. Remove the air inlet duct. 6. Loosen and remove the four bolts that secure the air intake resonator. 7. Loosen and remove the two bolts that secure the throttle body plenum. 8. Loosen hose clamp that secures the plenum to the throttle body. 9. Using a pair of piers, depress and pull back the hose clamp on the crank case vent at the cam cover. 10. Pull firmly upwards to remove the throttle body plenum. 11. Using a flat blade screwdriver, unclip the wire harness from the resonator. 12. Unclip the throttle cable and cruise control cable, then remove the resonator by pulling upwards. 13. Secure the throttle cable and cruise control cable to the stock clips. Install of Intake 14. Install the reducer and hose clamps onto the throttle body. Do not tighten at this time. 15. Remove the air temperature sensor from the throttle body plenum. 16. Install the air temperature sensor. NOTE: INSEPECT THE INSIDE OF THE TUBE FOR ANY DEBRIS, AND CLEAN THE INSIDE OUT WITH WATER AND A TOWEL. 17. Install the intake tube onto the throttle body. Tighten hose clamps at this time. 18. Secure the bracket to the rubber mounted. 19. Install the hose onto the crank case vent on the cam cover, then connect the other end to the vent on the intake tube. 20. Reconnect the air temperature sensor electrical connection. 21. Install the filter onto the intake tube and secure with the hose clamp. Adjust for best fit and clearance then tighten all hardware. 22. Reconnect the negative battery cable and double check to make sure everything is tightened and positioned before starting the vehicle. Resetting the ECU This is to be completed at your own risk. This procedure will reset the computer so that it may “learn” of your new intake. We are not to be held liable for any mishaps that you may occur while completing this process. • Disconnect the Negative battery cable for 5 minutes. • Reconnect the battery cable and false panel cover.

Incoming search terms:

c320 throttle body cleaning , 2005 kia sedona a/c diagram , air tube for vw bettle 1 8t , Air Flap Actuator for 2002 silverado , kia sedona 2005 2001 honda civic manual mpg , 2005 kia sorento ac diagram , 2005 kia sedona air conditioning system , 2005 Kia Sedona AC Diagram , online schematic for air conditioning for a 2003 Kia Sorento 3 5ltr v6 , does air ducts on 2005 kia sedona control heat , heater control switch for 2005 Buick century , how do i remove the upper ari intake module on a 2005 kia sorento , vacuum lines 01 honda civid cruise control , torque specs crank pulley 05 civic , how to clean 91 civic IAC , how to fix sticking temperature control flap in chevrolet pickup , how to install spring spacers honda trx 2011 , Parrot9100 User Manual , number of dual overhead cam sensors in infiniti qx4 , cwnter air vent for 2000 civic , cold air intake tube for 08 volvo vn670 , 2001 park avenue cabin air schematic , 2005 gmc 4500 wire diagram , 2005 honda crv thermometer sensor , 2005 kia sedona air cond fuse , 2005 mercedes benz c240 damper actuator NOT adv , a/c diagram for kia sedona 2005 , a/c duct on 2005 chevy 4500 , air conditioning on gmc4500 , air filter duct plymouth breeze 1998 , bell housing bolts on a 2005 sunfire , 05 trailblazer ss engine tork spec , civic 2005 propeller noise , where is the intake air temperature sensor on a Pontiac Grand Prix 2005

Comments are closed.

You might also likeclose